CENTURION 88A, 90A, 92A, 95A Professional Roller Derby Wheels
Part Number: STRUCENT
Hardness: Green=88A, Black=90A, Orange=92A, and White=95A
Diameter: 62mm
Profile: 30mm
Compound: Cast Urethane Special Custom Formula
Normally available from our Skates US Stock: All Hardnesses
Based on the Roll-Line tradition of the narrow wheels, the new Roll-Line CENTURION are the evolution of this concept.
Made whit the same compound, already famous for its performance, used for the Gladiator; these wheels will give you an extraordinary agility without compromising your grip and stability.
The new Roll-Line CENTURION 62mm X 30mm Professional Roller Derby Wheels represent the start of a whole new class of HIGH Performance Urethane Wheels specifically designed for Roller Derby. This very high quality wheel, is designed to be used on many types of skating surfaces including Skate Court, Sport Court, Concrete, standard wood floors coated with plastic or poly urethane, but also unusual surfaces like, tile type basketball and volleyball courts, tennis courts (Indoor or outdoor), and terrazzo surfaces that are more common around the World for Roller Derby.
The new Roll-Line CENTURION 62mm Professional Roller Derby Wheels utilize a stiff Delrin hub which is Strong, Light, and with Close Tolerances for Roundness, and Trueness, for the Cage where the Bearings and Spacers are mounted. The Roll-Line Tread is a cast secret Special Custom Urethane Formula, which provides exceptional Grip, while providing great ROLL and has a distinctive outer lip that provides that strong extra grip for tight spaces and turns. The Roll-Line GLADIATOR 62mm Professional Roller Derby Wheels have a little more feeling of spring or bounce as they have a higher REBOUND than most other Urethane wheels (except the Helium Indoor/Outdoor Wheels). This REBOUND creates a feeling of smoothness to the roll on the floor.
The Hub color identifies which hardness the wheels are.
88A = Green
90A = Black
92A = Orange
95A = White
The softer the wheel, or lower Shore “A” hardness number, the more the grip and slightly less roll. The harder the wheel, or higher Shore “A” number, the more the roll, with slightly less grip.
It is almost always recommended to use spacers in the wheels, when using standard 7mm bearings. Long ago, before the use of Lock Nuts (the nuts that have the Nylon Plastic inserts) to hold the wheels on the axles, Jam Nuts were used, but when the spacer was not as wide as the web of the wheel, or the wheel was not machined accurately, the bearings would lock up, the nut had to be tight, and could not be “backed-off”. This method, of locking the Axle Nut down, did promote proper bearing alignment and did increase the diameter of the axle from 7mm to approximately 14mm, because everything was locked down, which also saved the problems of bent axles. Today we do use Lock Nuts. It is still very advisable to lock everything down (especially for FreeStyle, Jam, and Roller Derby Skaters). Roll-Line does provide Spacers for Roll-Line Wheels with each pair of Frames or they can be purchased separately. Properly locking the Wheels down when using standard bearing types, will also promote longer bearing life.
The Roll-Line 7mm and 8mm SpeedRace & SpeedMax Bearings , are specifically made for very High Level Competitive Roller Skating of all types, including Roller Derby and are a very Durable Bearing with lots of ROLL. The SpeedRace & SpeedMax Bearings are Free Rolling with minimal Radial Play which promotes and very evenly distributes the load across the 7 or 8 (of the SpeedMax) balls for optimal Roll and a good amount of Axial Play or Thrust, which is the side movement of the inner race in relation to the outer race. This movement is very important because when Skaters push, we always put side load on the skate to get power in the push or stroke. If the Bearing does not allow for this, it will bind and LOOSE operating speed or ROLL. These provisions in the Race Curvature and Contact Angle allow the Roll-Line SpeedRace & SpeedMax Bearings to ROLL very freely.
The Roll-Line SpeedRace Bearings If they work for World level FreeStyle Skaters, they will easily work for and withstand the riggors of Roller Derby.
Please allow 7 days for all Roll line orders to process before shipping.
